PC(聚碳酸酯)EXL6013/沙伯基礎(SABIC)

PC(聚碳酸酯)EXL6013/沙伯基礎(SABIC)_價格_物性_圖片_UL黃卡

公司主營產品:耐高溫塑料,耐低溫塑料,耐磨塑料,耐熱塑料,耐寒塑料,防火塑料,加纖塑料,醫療級/食品級塑料,抗紫外線塑料,紅外線穿透塑料...

全國24小時銷售熱線:

0769-83023208

產品詳情

?            SABIC(沙伯基礎創新塑料)LEXAN PC EXL6013是專為要求具有高沖擊性能和優于標準聚碳酸酯的耐化學性的應用而開發的。

以下是SABIC沙伯基礎創新Lexan PC EXL6013中英文物性表資料:

PROPERTIES TYPICAL VALUESUNITSTEST METHODS
MECHANICAL



Taber Abrasion, CS-17, 1 kg
10mg/1000cySABIC method
Tensile Stress, yield, 50 mm/min
55MPaISO 527
Tensile Stress, break, 50 mm/min
60MPaISO 527
Tensile Strain, yield, 50 mm/min
7%ISO 527
Tensile Strain, break, 50 mm/min
100%ISO 527
Tensile Modulus, 1 mm/min
2100MPaISO 527
Flexural Stress, yield, 2 mm/min
80MPaISO 178
Flexural Modulus, 2 mm/min
2150MPaISO 178
Ball Indentation Hardness, H358/30
90MPaISO 2039-1
IMPACT



Izod Impact, unnotched 80*10*3 +23°C
NBkJ/m2ISO 180/1U
Izod Impact, unnotched 80*10*3 -30°C
NBkJ/m2ISO 180/1U
Izod Impact, notched 80*10*3 +23°C
70kJ/m2ISO 180/1A
Izod Impact, notched 80*10*3 -30°C
60kJ/m2ISO 180/1A
Charpy 23°C, V-notch Edgew 80*10*3 sp=62mm
75kJ/m2ISO 179/1eA
Charpy -30°C, V-notch Edgew 80*10*3 sp=62mm
70kJ/m2ISO 179/1eA
Charpy 23°C, Unnotch Edgew 80*10*3 sp=62mm
NBkJ/m2ISO 179/1eU
Charpy -30°C, Unnotch Edgew 80*10*3 sp=62mm
NBkJ/m2ISO 179/1eU
THERMAL



Thermal Conductivity
0.2W/m-°CISO 8302
CTE, 23°C to 80°C, flow
7.E-051/°CISO 11359-2
CTE, 23°C to 80°C, xflow
7.E-051/°CISO 11359-2
Ball Pressure Test, 125°C +/- 2°C
PASSES-IEC 60695-10-2
Vicat Softening Temp, Rate B/50
138°CISO 306
Vicat Softening Temp, Rate B/120
140°CISO 306
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm
131°CISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm
122°CISO 75/Ae
PHYSICAL



Mold Shrinkage on Tensile Bar, flow
0.6-0.8%SABIC method
Density
1.2g/cm3ISO 1183
Water Absorption, (23°C/saturated)
0.35%ISO 62-1
Moisture Absorption (23°C / 50% RH)
0.15%ISO 62
Melt Volume Rate, MVR at 300°C/1.2 kg
5cm3/10 minISO 1133
ELECTRICAL



Volume Resistivity
>1.E+15Ohm-cmIEC 60093
Surface Resistivity, ROA
>1.E+15OhmIEC 60093
Dielectric Strength, in oil, 3.2 mm
17kV/mmIEC 60243-1
Relative Permittivity, 1 MHz
2.7-IEC 60250
Dissipation Factor, 50/60 Hz
0.001-IEC 60250
Dissipation Factor, 1 MHz
0.01-IEC 60250
Comparative Tracking Index
175VIEC 60112
Relative Permittivity, 50/60 Hz
2.7-IEC 60250
FLAME CHARACTERISTICS



Glow Wire Flammability Index 850°C, passes at
1mmIEC 60695-2-12
Injection Molding



Drying Temperature
120°C
Drying Time
2-4hrs
Maximum Moisture Content
0.02%
Melt Temperature
290-320°C
Nozzle Temperature
280-310°C
Front - Zone 3 Temperature
290-320°C
Middle - Zone 2 Temperature
280-310°C
Rear - Zone 1 Temperature
270-300°C
Hopper Temperature
60-80°C
Mold Temperature
80-120°C



上一篇:PC(聚碳酸酯)EXL5429/沙伯基礎(SABIC)

下一篇:PC(聚碳酸酯)EXL1444/沙伯基礎(SABIC)

欣隆全塑膠
相關產品

Related products

推薦產品
(*^▽^*)MG海王星王国APP下载 成都单机麻将血战到底 广东快乐10分钟 十一选五开奖结果云南一定牛 湖南快乐十分开奖官网 516棋牌游戏中心? 麻将来了下不过i 微乐捉鸡麻将二丁拐技巧 欢乐炸金花2016版下载 黑龙江11选5前三组走势图 江苏七位数体彩2元网 最新赌博导航 北京麻将牌怎么玩 gtv网络棋牌频道 湖北麻将血流成河下载 快乐双彩中奖条件 澳洲快乐8计划软件